OBX Sub-frame Reinforcement kit for the EG, DC, EK Honda chassis allows the driver to fine tune the driving characteristics of the car with the use of OEM or larger aftermarket sway bars without the risk of tearing the stock mounting locations. Great for those who autocross, circuit race, or just those who want spice up a daily driver. Available in 19mm to 24mm sway bar sizes. Reinforcement brace is made from 6061-T6 aluminum and is available in satin silver, flat black, gold, red, and blue colors.
Disclaimer
All Honda parts listed on this page/website such as vehicle names, make, model, sub-model, engine and chassis codes and logos are registered trademarks of American Honda Motor Corporation, Inc and are used for application reference or identification purposes only. OBX Racing Sports is the manufacturer of aftermarket tuning parts of use in the equipment of various automobile manufacturers. OBX Racing sports and the parts contained herein are not sponsored, affiliated, associated, licensed nor authorized or otherwise connected in anyway with America Honda Motor Corporation, Inc the original equipment manufacturers shown on this page/website. Trades, service marks, and trade names of OBX Racing Sports Parts (TM) used in this site are trade names or trademarks of the respective brand and products of OBX Racing Sports (TM).
Drag Race Spec. Axle/Hub Kit for Honda B-Series
OBX Drag Race Spec Axles are a definite must for any enthusiast that is putting up SERIOUS horsepower numbers. The CV design on this axle is built to handle 1000+ horsepower.
Our axles are compatible with the standard spline size on the differential end for easy installation and are compatible with OEM or aftermarket drop-in differentials as well as differential spools.
Along with the axles are new hubs that fit the stock bearing sizes as well as new extended studs for installation. New ABS rings have already been installed on the axles.
Billet Engine Mount Kits for K-Series Swaps
OBX Billet Engine Mount Kits are specifically designed to make engine swap headaches a thing of the past. All the necessary mounts and brackets are included to perform complete drop-in swaps.
The kit allows for optimized engine placement for ground clearance and axle angles for optimum drivability on the street or track. The degree rating of the urethane is measured in regards to the stiffness of the bushing for the perfect ride quality. Available for K-series engine swaps for Acura Integra and Honda Civic.
Disclaimer
All Honda parts listed on this page/website such as vehicle names, make, model, sub-model, engine and chassis codes and logos are registered trademarks of American Honda Motor Corporation, Inc and are used for application reference or identification purposes only. OBX Racing Sports is the manufacturer of aftermarket tuning parts of use in the equipment of various automobile manufacturers. OBX Racing sports and the parts contained herein are not sponsored, affiliated, associated, licensed nor authorized or otherwise connected in anyway with America Honda Motor Corporation, Inc the original equipment manufacturers shown on this page/website. Trades, service marks, and trade names of OBX Racing Sports Parts (TM) used in this site are trade names or trademarks of the respective brand and products of OBX Racing Sports (TM).
High Performance Fuel Injectors
OBX Ultra-flow fuel injectors are now available in low/high impedance types. Designed for side feed or top feed systems, our injectors come in varieties of flow ratio from 310cc~2000cc upgrades for naturally aspirated vehicles or turbo charged vehicles.
OBX products are priced competitively, to meet any budget oriented enthusiast. Backed by manufacturer warranty for 3 years/36,000 miles.
Please contact your local authorized dealers or check back with us at www.obxracingsports.com for upcoming specific applications. Private label branding also available.
OEM Replacement Oxygen Sensors
OBX Oxygen Sensors are designed to meet or exceed today's strict emission standards. Intended as replacements for OEM O2 sensors, our product is built with exacting quality to ensure optimum fuel efficiency while allowing your engine to run at peak performance.
Our sensors are made of the highest quality materials to ensure consistent performance along with extreme durability and life. Our design consists of a Zirconia trap layer along with a porous Teflon PTFE filter encased with a double heat protection layer all enclosed within a stainless steel housing. The high-end materials and design itself is meant to last the life of the vehicle.
All our effort into producing this sensor translates into lower emissions and improved fuel economy which is extremely important in today's economy. Our sensors are manufactured to provide the most accurate readings for a vehicle's ECU to optimize air/fuel ratio and ignition timing for optimum performance and efficiency. Great for tune ups and passing SMOG tests.
Available for most makes and models. Contact your local retailer or one of our many online resellers for the right sensor for your application.
OEM Replacement Oxygen Sensors
OBX Oxygen Sensors are designed to meet or exceed today's strict emission standards. Intended as replacements for OEM O2 sensors, our product is built with exacting quality to ensure optimum fuel efficiency while allowing your engine to run at peak performance.
Our sensors are made of the highest quality materials to ensure consistent performance along with extreme durability and life. Our design consists of a Zirconia trap layer along with a porous Teflon PTFE filter encased with a double heat protection layer all enclosed within a stainless steel housing. The high-end materials and design itself is meant to last the life of the vehicle.
All our effort into producing this sensor translates into lower emissions and improved fuel economy which is extremely important in today's economy. Our sensors are manufactured to provide the most accurate readings for a vehicle's ECU to optimize air/fuel ratio and ignition timing for optimum performance and efficiency. Great for tune ups and passing SMOG tests.
Available for most makes and models. Contact your local retailer or one of our many online resellers for the right sensor for your application.
Supercharger Tuner Kits
OBX is proud to introduce our new Supercharger Tuner Kits. These kits utilize a centrifugal supercharger for optimum power for both street and strip applications. These kits provide superior flow while providing near silent operation and extreme reliability. Tuner kits do not include fuel and engine management hardware to allow for custom tuning. Currently available for the 99-10 Ford Mustang V8 and 97-10 Chevrolet Corvette.
Volvo S60/60R Exhaust System
Direct bolt on full stainless steel cat. back systems. Fitments for the FWD and AWD applications.
Disclaimer: “For off-road competition/racing use only. This product is not intended to be installed on vehicles registered for highway use. LEGAL IN CALIFORNIA ONLY FOR RACING VEHICLES THAT MAY NEVER BE USED, OR REGISTERED OR LICENSED FOR USE, UPON A HIGHWAY.”
Volvo S60/60R Exhaust System
Direct bolt on full stainless steel cat. back systems. Fitments for the FWD and AWD applications.
Disclaimer: “For off-road competition/racing use only. This product is not intended to be installed on vehicles registered for highway use. LEGAL IN CALIFORNIA ONLY FOR RACING VEHICLES THAT MAY NEVER BE USED, OR REGISTERED OR LICENSED FOR USE, UPON A HIGHWAY.”
OBX Exhaust Catback 2010-17 Ford Taurus SHO V6 3.5L AT AWD 4DR 2010 -13 Lincoln MKS Ecoboost Ford V6 AT AWD 4DR.
OBX Exhaust Catback For 2010 thru 2017 Ford Taurus SHO V6 3.5L AT AWD 4DR 2010 thru 2013 Lincoln MKS Ecoboost Ford V6 Engine AT AWD 4DR 3.5L
Disclaimer: “For off-road competition/racing use only. This product is not intended to be installed on vehicles registered for highway use. LEGAL IN CALIFORNIA ONLY FOR RACING VEHICLES THAT MAY NEVER BE USED, OR REGISTERED OR LICENSED FOR USE, UPON A HIGHWAY.”
